TOP MOST Machine Design
Quiz
- Guest’s theory of failure is applicable for following type of materials
- brittle
- ductile
- elastic
- plastic
- Cold working
- increases the fatigue strength
- decreases the fatigue strength
- has no influence on fatigue strength
- alone has no influence on fatigue strength
- In Vicker’s hardness testing, the pyramid indentor apex is
- 40°
- 122°
- 136°
- 152°
- Coaxing is the procedure of increasing
- metal strength by cycling
- metal hardness by surface treatment
- metal resistance to corrosion by coating
- fatigue limit by overstressing the metal by successively increasing loadings
- The property of a material which enables it to resist fracture due to high impact loads is known as
- elasticity
- endurance
- strength
- toughness
- Tensile strength of a mild steel specimen can be roughly predicted from following
hardness test- Brinell
- Rockwell
- Vicker
- Shore’s sceleroscope
- Resistance to fatigue of a material is measured by
- Young’s modulus
- coefficient of elasticity
- elastic limit
- endurance limit.
- Which process will increase the fatigue duration of parts ?
- finishing and polishing
- shot-peening
- decarburisation
- electroplating
- Rankine’s theory of failure is applicable for following type of materials
- brittle
- ductile
- elastic
- plastic
- Stress concentration in static loading is more serious in
- ductile materials
- brittle materials
- equally serious in both cases
- depends on other factors
- Other method of reducing shock load in the above case can be
- to decrease length
- to increase length
- unaffected by length
- other factors would decide same
- Brittle coating technique is used for
- determining brittleness
- protecting metal against corrosion
- protecting metal against wear and tear
- experimental stress analysis
- Stress concentration is caused due to
- variation in properties of material from point to point in a member
- pitting at’points or areas at which loads on a member are applied
- abrupt change of section
- all of the above
- Stress concentration in cyclic loading is more serious in
- ductile materials
- brittle materials
- equally serious in both cases
- depends on other factors
- The function of a washer is to
- provide cushioning effect
- provide bearing area
- absorb shocks and vibrations
- provide smooth surface in place of rough surface
- The notch angle of the Izod impact test specimen is
- 10°
- 20°
- 30°
- 45°
- Pick up wrong statement. Fatigue strength can be increased by
- cold working
- shot peening
- grinding and lapping surface
- hot working
- The endurance limit of a material with finished surface in comparison to rough
surface is- more
- less
- same
- unpredictable
- Maximum principal stress theory is applicable for
- ductile materials
- brittle materials
- elastic materials
- none of the above.
- Resilience of a material is important, when it is subjected to
- combined loading
- shock loading.
- thermal stresses
- wear and tear
- If a material fails below its yield point, failure would be due to
- straining
- fatigue
- creep
- sudden loading
- The crest diameter of a screw thread is same as
- major diameter
- minor diameter
- pitch diameter
- core diameter
- The following type of nut is used with alien bolt
- alien nut
- hexagonal nut
- slotted nut
- any one of the above.
- A stud
- has a head on one end and a nut fitted to the other
- has head at one end and other end fits into a tapped hole in the other part to be joined
- has both the ends threaded
- has pointed threads
- A tap bolt
- has a head on one end and a nut fitted to the other
- has head at one end and other end fits into a tapped hole in the other part o be joined
- has both the ends threaded
- has pointed threads
- Cap screws are
- similar to’small size tap bolts except that a greater variety of shapes of heads are available
- slotted for a screw driver and generally used with a nut
- used to prevent relative motion be-tween parts
- provided with detachable caps
- An alien bolt is
- self locking bolt
- same as stud
- provided with hexagonal depression in head
- used in high speed components
- Ball bearing type screws are found in following application
- screw jack
- aeroplane engines
- crane
- steering mechanism
- Set screws are
- similar to small size tap bolts except that a greater variety of shapes of heads are available
- slotted for a screw driver and generally used with a nut
- used to prevent relative motion be-tween parts
- similar to stud
- A self locking screw has
- fine threads
- coarse threads
- coefficient of friction > tangent of load angle
- hole for inserting split pin
Click On Show All Questions Button To View All Questions :-
No comments:
Post a Comment